SmartgridOne - Software version 1.29.0.1
‍

SmartgridX & App

What's new in the platform & app - a refreshed experience across the SmartgridX portal and the mobile app.

Revamped landing page
We've given the landing page a stylish revamp. It now more clearly highlights which energy flows are currently present, whether data is up to date, and if there are any active issues. For each energy asset, additional information about its current state and control mode is just a tap away.

Streamlined navigation
Getting around the app is now more intuitive. We've introduced a new bottom navigation menu so your most important screens, such as the Overview page and the Planning (Prices) view, are always just a tap away.

Expanded price configurator - now Wallonia
Our price configurator offers quick configuration wizards depending on the currency and country of a controller. Following the Flanders wizard, this version adds a dedicated interface for entering dynamic contracts for customers in Wallonia. Energy tariffs can be fully configured by entering the dynamic price formula used by the energy provider, picking a DSO (e.g. ORES, AIEG, RESA, …) and a distribution rate (simple / bihoraire / impact).

Improved site & device overview
The device overview page in SmartgridX has been reworked so charts are more compact and intelligently sized to make the most of the available screen space. Charts now feature a shared crosshair when hovering and automatically share the same time range, making it easier than ever to analyze data streams over time.

Minor changes

• All node types supported (SmartgridX): Device types that were previously not recognized by SmartgridX, such as switched loads and various types of boilers and heat pumps, are now fully supported and visualised.
  
  ‍

Highlights

The biggest new capabilities in this release.

Richer commissioning data page
The data page in the commissioning interface now shows significantly more information, making it much easier to follow up on an installation on-site. Improved external-signal feedback messages and a new duplicate-device warning help installers catch configuration issues before they become problems.

Smarter heat pump cost optimization
Heat pumps in cost-optimization mode are now more likely to boost when energy prices are low, capturing cheap energy more aggressively and improving overall running costs for the end customer.

New Integrations

These devices are now supported in SmartgridOne.

Sunsynk Inverters
Monitoring and control support for Sunsynk inverters.

Read the docs →

Dyness Hybrid Inverters
Support for Dyness hybrid inverters, including energy-meter readout via the refactored DH100F driver.

Read the docs →

Smappee EV Charger (MQTT)
Smart charging control for Smappee EV chargers over MQTT.

Read the docs →

Huawei FusionCharge EV Chargers
Charging session management and smart control for Huawei FusionCharge chargers.

Read the docs →

Veton Charging Stations
Added support for Veton charging stations.

Read the docs →

Libattion MBMS Batteries
Monitoring and control for Libattion MBMS battery systems.

Read the docs →

Weiheng EMS100
Added support for the Weiheng EMS100 system.

Read the docs →

Hager ECR / ECA Series
Added support for Hager ECR and ECA series energy meters.

Read the docs →

SmartgridOne Improvements

External Signals

• Fusebox: Improvements to the Fusebox external signal.
• VGT signals: Increased reaction speed to VGT external signals.
• Teleport API: Power setpoint adjusted to use negative values for charging.
• Commissioning feedback: Improved feedback messages for external signals in the commissioning interface.

System & Control

• Heat pump cost optimization: More likely to boost when energy prices are low.
• Energy balance: Sites without batteries now derive autoconsumption directly from metered energy deltas.
• Solis control precision: Improved control precision for Solis solar inverters.
• Grid support warning: Frontend now warns that peak shaving will be enforced when grid support is on but the battery is not in peak shaving mode.
• I/O controller feedback: Internal API now reports when the I/O controller is in a halted state.
• Sungrow status: Added status messages for the internal state of Sungrow Hybrid inverters.

Commissioning & Frontend

• Data page: More information on the commissioning data page for easier installation follow-up.
• Duplicate-device warning: Frontend warns when a driver detects many doubles before a user adds them all.
• SolaX G4 RS485: Added RS485 support for SolaX G4 inverters and energy meters.
• Blitzpower whitelabel: Added support for the whitelabeled version of the Blitzpower EV charger.

Driver Refactors

• Dyness DH100F: Refactored to also support reading out energy meters.
• Siemens PAC: Energy meter driver refactored.
• Youless P1 dongle: Refactored, with a fix for missing measurements.
• FoxESS H3: New driver.
• Simulation devices: Driver refactored.
• GoodWe ESS: Refactored to improve EMS power handling and manufacturer code validation.

Stability Improvements

• Myenergi Zappi: Driver bugfixes.
• SMA cloud driver: Bugfixes.
• Enerlution HYTH: Added detection for an unimplemented power register.
• Tecloman HPS & meters: Fixed reactive power scaling.
• Deye 1ph: Fixed single-phase control.
• Poweroad C-BMS: Fixed backwards compatibility with older settings.
• GoodWe GridTied SMT: Fixed handling of inverters without power readings.
• Frontend logos: Visual fix for logos in the frontend.

‍